Product Data Sheet Sika MonoTop-4012 April 2022, Version 03.01 020302040030000320 PRODUCT DATA SHEET Sika MonoTop-4012 High performing more sustainable R4 concrete repair mortar PRODUCT DESCRIPTION Sika MonoTop-4012 is a one-part, cementitious, fibre reinforced, low shrinkage repair mortar. % : +41 58 436 40 40 Bonding primer/ Reinforcement corrosion protection, ~500 m/m (+20 C / 65 % relative humidity at 28 days), Chloride diffusion coefficient: 4,8 x 10-12 m2/s. <>stream Imprint Reinforcement corrosion protection coating. Where layers are to be built up, to prevent sagging or slumping, each layer must be allowed to harden before applying subsequent layers wet on wet. Curing compounds must not be used when they could adversely affect subsequently applied products and systems. Restoration work (Principle 3, method 3,1 and 3,3 of EN 1504-9). curing compound, moist geotextile membrane, polythene sheet, etc. The product must be stored in original, unopened and undamaged packaging in dry conditions at temperatures between +5 C and +35 C. Mix thoroughly for at least for 3 minutes adding additional water if necessary, to the maximum specified amount. When manually applying by hand, first make a scratch coat by firmly scraping the repair mortar over the substrate surface to form a thin layer and fill any pores or cavities in the surface. endstream Preserving or restoring passivity (Principle 7, method 7.1 and 7.2 of EN 1504-9) - Increasing cover with additional mortar and replacing contaminated or carbonated concrete, Structures requiring a Class R4, R3, R2 orR1 mortar, Conformity with LEED v4 MRc 2 (Option 1): Building Product Disclosure and Optimization Environmental Product Declarations, Conformity with LEED v4 MRc 3 (Option 2): Building Product Disclosure and Optimization - Sourcing of Raw Materials, Conformity with LEED v4 MRc 4 (Option 2): Building Product Disclosure and Optimization - Material Ingredients, IBU Environmental Product Declaration (EPD), CE Marking and Declaration of Performance to EN1504-3 - Concrete repair product for structural repair, High / ultra-high pressure water blasting equipment. When a bonding primer is required to achieve the required adhesion values, use Sika MonoTop-1010 or SikaTop Armatec-110 EpoCem. Keep the surface wet and do not allow to dry. Refer to the individual Product Data Sheets. Contact Us. It is based upon Sika proven and . <>stream Sika MonoTop-4012 Reduced carbon footprint Smoothing/ levelling mortar Sika MonoTop-3020 Reduced carbon footprint APPLICATION INFORMATION Mixing Ratio For brush application ~5,25 L water (21 %) per 25 kg bag . Uses recycled waste materials Layer thickness 6-120 mm. Cementitious R4 concrete repair mortar containing recycled waste materials. Structural Repair Mortar Sika MonoTop-412 TH is a 1-component, fibre reinforced, low shrinkage structural repair mortar in accordance with EN 1504-3 class-R4. PRODUCT DATA SHEET Sika MonoTop-3020 August 2020, Version 01.01 020302050010000114 3 / 4. coat by firmly scraping the mortar over the substrate Hij bevat gerecycleerde materialen en vermindert daardoor zijn koolstofvoetafdruk. Store bags in a warm environment and using warm water to assist with achieving strength gain and maintaining physical properties. Repair of spalling and damaged concrete in infrastructure and superstructure works. Application in the direct sun or strong winds. Description Sika MonoTop-622 F is a one-component, microfibre-reinforced, polymer-modified and early strength-gaining, cementitious mortar for horizontal and vertical concrete repair and resurfacing. It contains recycled waste materials and can reduce the carbon footprint application activity calculations. Resource Center. Hardened material can only be mechanically removed. Este nuevo mortero de reparacin estructural es la evolucin del exitoso Sika MonoTop-412 S que ha permanecido en nuestra gama durante ms de una dcada. Sika MonoTop-910N). Consider storing bags in a cool environment and using cold water to assist with controlling the exothermic reaction to reduce cracking and maintaining physical properties. Thoroughly pre-wet the prepared substrate (2 hours recommended) before application. Sustainability Portfolio Management. Apply the scratch coat over the complete substrate surface to form a thin layer to fill surface pores or cavities. <>stream Add additional water up to 1 gallon total. curing compound, moist geotextile membrane, polythene sheet, etc. Apply repair mortar onto bonding primer wet on wet. Remove excess water from within the surface pores and cavities e.g. Structural strengthening (Principle 4, method 4.4 pf EN 1504-9). xMn!LaTuQ2LM_(H`}^&niQj"fet:(` Surface finish to the required surface texture using a stainless steel, steel, PVC or wooden float. Increasing the bearing capacity of the concrete structure by adding mortar. PRODUCT DATA SHEET Sika MonoTop-412 TH December 2019, Version 02.01 020302040030000221 PRODUCT DATA SHEET Sika MonoTop-412 TH STRUCTURAL REPAIR MORTAR DESCRIPTION Sika MonoTop-412 TH is a 1-component, fibre rein-forced, low shrinkage structural repair mortar in ac-cordance with EN 1504-3 class-R4. E6L )~gSImcF`ZCd \t0EWftjtS . USES : +27 31 792 6500 Product Data Sheet (PDS) PDF - 249 KB (en) SikaFiber Novocon XR. Where a reinforcement coating is required, apply to the whole exposed circumference Sika MonoTop-1010 or SikaTop Armatec-110 EpoCem. with a clean sponge. Heat of hydration minimized to extend working time, especially in warm conditions. Repair of spalling and damaged concrete in infrastructure and superstructure works. Sika Corporation. Preserving or restoring passivity (Principle 7, method 7,1 and 7,2 of EN 1504-9) - Increasing cover with additional mortar and replacing contaminated or carbonated concrete, Structures requiring a Class R4, R3, R2 orR1 mortar, Conformity with LEED v4 MRc 2 (Option 1): Building Product Disclosure and Optimization Environmental Product Declarations, Conformity with LEED v4 MRc 3 (Option 2): Building Product Disclosure and Optimization - Sourcing of Raw Materials, Conformity with LEED v4 MRc 4 (Option 2): Building Product Disclosure and Optimization - Material Ingredients, IBU Environmental Product Declaration (EPD), CE Marking and Declaration of Performance to EN1504-3 - Concrete repair product for structural repair, High / ultra-high pressure water blasting equipment. Adjust to the required consistency to achieve a smooth consistent mix. Product Data Sheet Sika MonoTop-4012 ZA August 2022, Version 01.02 020302040030000501 PRODUCT DATA SHEET Sika MonoTop-4012 ZA Cementitious R4 concrete repair mortar containing recycled waste materials DESCRIPTION Sika MonoTop-4012 ZA is a 1-part, cementitious, fibre reinforced, low shrinkage repair mortar. Structural strengthening (Principle 4, method 4,4 pf EN 1504-9). PRODUCT DATA SHEET Edition 07.2018/v1 CSC Master Format TM 03 01 00 Protect fresh mortar immediately from premature drying using an appropriate curing method, e.g. Surface finish to the required surface texture using a stainless steel, steel, PVC or wooden float. Thoroughly pre-wet the prepared substrate for a minimum of 2 hours before application. Any bonding primer shall be applied on a pre-wet substrate and subsequent ap-plication of the repair mortar shall be applied wet on wet with the bonding primer. While stirring slowly, add the powder to the water. On a well prepared and roughened substrate or for a sprayed application, a bonding primer is generally not required. Keep the surface wet and do not allow to dry. May only be used by experienced professionals. Hardened material can only be mechanically removed. Strictly follow installation procedures as defined in method statements, application manuals and working instructions which must always be adjusted to the actual site conditions. It contains recycled waste materials and can reduce the carbon footprint application activity calculations. Excelente trabajabilidad. Before application remove excess water, e.g. Refer to the individual Product Data Sheets. Place the wet mixed Sika MonoTop-4012 into the spraying equipment. Sika MonoTop-412 MY is a single component, fibre reinforced, low shrinkage structural repair mortar. Tensile Adhesion Strength > 1.5 N/mm (with bonding bridge) (ASTM D4541) Water Absorption < 3 % (at 30 mm) (BS 1881: Part 122) SYSTEM INFORMATION System Structure Sika MonoTop System comprises: Region Area / Country Site Go Go to Sika Global website Contact My Sika Product Data Sheet Sika MonoTop-412 N January 2020, Version 01.02 020302040030000204 PRODUCT DATA SHEET Sika MonoTop-412 N R4 FIBRE REINFORCED STRUCTURAL REPAIR MORTAR DESCRIPTION Sika MonoTop-412 N is a 1-component, fibre rein-forced, low shrinkage repair mortar meeting the re-quirement of class-R4 of EN 1504-3. Select the most appropriate equipment required for the project: High or ultra-high pressure water blasting equipment. Spray the repair mortar onto the pre-wetted substrate between the minimum and maximum layer thicknesses without the formation of voids. 06/04/2022. Mix to a uniform consistency, maximum . Superior workability Suitable for hand and machine application Can be applied up to 50 mm thick per application layer PRODUCT DATA SHEET Sika MonoTop-1010 August 2020, Version 01.02 020302020010000054 2 / 4. Place the wet mixed Sika MonoTop-4012 into the spraying equipment. Sika MonoTop-4012 is a 1-part, cementitious, fibre reinforced, low shrinkage repair mortar. Repair of spalled concrete caused by reinforcement corrosion. Contains integral corrosion inhibitor based on proven technology. %PDF-1.7 endobj Do not add water during the surface finishing as this can cause discolouration and cracking. Product Data Sheet Sika MonoTop-612 September 2019, Version 01.02 020302040030000196 2 / 4. utes to corrosion shall be removed. Sika India Pvt. Make a scratch coat using the repair mortar. x[ }x 4l6cjw9@b%R%eK6pFUo7`6x<8F= s. It contains re- The wet mixed Sika MonoTop-4012 must be placed into the spraying equipment and applied onto the pre-wetted substrate (pre-wet procedure as hand application) between the minimum and maximum layer thicknesses without the formation of voids. Repairs to all types of reinforced concrete structures and components for: Sustainability / Certifications / Approvals, Hand and machine application (wet spray technique). PRODUCT DATA SHEET Sika MonoTop-412 MY November 2019, Version 01.01 020302040030000167 2 / 4. Strictly follow installation procedures as defined in method statements, application manuals and working instructions which must always be adjusted to the actual site conditions. Select the most appropriate equipment required for the project: Also refer to Site Handbook Repair of Concrete Structures Patch Repair and Spray Applications. Protect fresh mortar immediately from premature drying using an appropriate curing method, such as curing compound, moist geotextile membrane or polythene sheet. Allow each layer to slightly harden and remain wet before applying subsequent layers. Technical Information Property Value, Unit Adjust to the required consistency to achieve a smooth consistent mix. Vis mer Inneholder resirkulerte delmaterialer Sjikttykkelser: 6-120 mm Make a scratch coat using the repair mortar. with a clean sponge. endobj J8_Zx>Q w^#8 Gradually add the powder to the water while stirring slowly. 3. Application up to 120 mm in 1 layer Sika MonoTop-4012 can be applied in layers with thickness between 6 and 120 mm, with a fresh density of 2.1 kg/L. This figure is theoretical and does not allow for any additional material due to surface porosity, surface profile, variations in level or wastage etc. Consumption depends on the roughness and absorbency of the substrate. Mix thoroughly for at least for 3 minutes, add additional water if necessary. Sika MonoTop-4012 may only be used by experienced professionals. EpoCem (consult Product Data Sheet). Thoroughly pre-wet the prepared substrate (2 hours recommended) before application. Sika MonoTop-1010 is a 1-part, cementitious, polymer modified coating material used as bonding primer and reinforcement corrosion protection. Large quantities or machine application - suitable forced action mixer, Wet Spray - All in one mixing and spraying machine or separate spraying machine and all associated ancillary equipment to suit application volumes. Tel. The product must be stored in original, unopened and undamaged packaging in dry conditions at temperatures between +5 C and +35 C. Priming For priming of reinforcing steel use Sika Armatec 110 EpoCem (consult Technical Data Sheet). Small quantities - low speed electric single or double paddle mixer (<500 rpm). Sika MonoTop-4012 is a 1-part, cementitious, fibre reinforced, low shrinkage repair mortar. Clean all tools and application equipment with water immediately after use. SIKA apuesta por el concepto de sostenibilidad en este nuevo desarrollo de producto, contribuyendo a la reduccin en la emisin de CO2 por el uso de material reciclado en su . Protect freshly applied material from freezing and frost to prevent cracking. E-mail: [emailprotected], Cementitious R4 concrete repair mortar containing recycled waste materials. Curing compounds must not be used when they could adversely affect subsequently applied products and systems. 9 Hocking Place Increasing the bearing capacity of the concrete structure by adding mortar. H<3^4Yg3nNM~oWE[mWqE/, f>sP.[Q=|\T/x#@lS^~_$DuuW`may9.6.O^NH&w+tu~lr5u?d]D]dRJ$Q34s,}|LCNV# The surface must appear a dark matt appearance without shining and surface pores and cavities must not contain water. with a clean sponge. Filling / repair mortar for voids, honeycombed areas. Superior workability Suitable for hand and machine application Can be applied up to 35 mm thick per layer Product Data Sheet Safety Data Sheet Show all documents Overview Product Details As a Do not add water during the surface finishing as this can cause discolouration and cracking. Downloads. Title: Sika MonoTop-1010 Note: When a bonding primer is required to achieve the required adhesion values, use Sika MonoTop-1010 or SikaTop Armatec 110 EpoCem (Refer to individual Product Data Sheets). Product Data Sheet Sika MonoTop-412 NFG August 2020, Version 01.02 020302040030000215 PRODUCT DATA SHEET Sika MonoTop-412 NFG R4 Repair Mortar with Corrosion Inhibitor DESCRIPTION Sika MonoTop-412 NFG is a 1-component, polymer modified, fibre reinforced, low shrinkage repair mor-tar with corrosion inhibitor meeting the requirement Formulated with inert, non-reactive aggregates to eliminate potential Alkali-Aggregate Reactivity (AAR). Small quantities: low speed electric single or double paddle mixer (< 500 rpm). Apply product to a test area to calculate the exact consumption for the specific substrate conditions and proposed application equipment. Small quantities: low speed electric single or double paddle mixer (<500 rpm). It contains re- It contains re- Where a reinforcement coating is required, apply to the whole exposed circumference Sika MonoTop-1010 orSikaTop Armatec 110 EpoCem (Refer to individual Product Data Sheet(s)). Marine, tunnels, bridges and buildings structures Advantages To be mixed with water only Excellent workability Adjustable consistency APPLICATION INFORMATION Mixing Ratio 3.5-4.0 L of water for 25 kg powder Consumption Depends on the substrate roughness and thickness of layer applied. 3608, Westmead KwaZulu-Natal, Tel. Pour the minimum recommended clean water quantity into a suitable mixing container / equipment. Consider storing bags in a cool environment and using cold water to assist with controlling the exothermic reaction to reduce cracking and maintaining physical properties. %PDF-1.7 Note: Do not add more water than the maximum specified amount. Store bags in a cool environment and using cold water to assist with controlling the exothermic reaction to reduce cracking and maintaining physical properties. It contains recycled waste materials and can reduce the carbon footprint application activity calculations. <>stream Always refer to packaging. Repair of spalling and damaged concrete in infrastructure and superstructure works. Product Data Sheet Sika MonoTop-4012 September 2021, Version 02.01 020302040030000320 PRODUCT DATA SHEET Sika MonoTop-4012 Cementitious R4 concrete repair mortar containing recycled waste materials DESCRIPTION Sika MonoTop-4012 is a 1-part, cementitious, fibre reinforced, low shrinkage repair mortar. Data Sheet for the product concerned, copies of which will be supplied on request. Product Data Sheet Sika MonoTop R July 2017, Version 01.01 020302040030000208 1 / 3. Sika MonoTop-4012 is a 1-part, cementitious, fibre reinforced, low shrinkage repair mortar. Allow each layer to slightly harden and remain wet before applying subsequent layers. Restoration work (Principle 3, method 3.1 and 3.3 of EN 1504-9). 5 0 obj Product Data Sheet Sika MonoTop-1010 March 2021, Version 01.01 020302020010000054 4 / 4. Product Data Sheet Sika MonoTop-4012 November 2021, Version 02.01 020302040030000320 4 / Remove excess water from within the surface pores and cavities e.g.
Calories Quiche No Crust, Deductive Method Of Teaching Mathematics Examples, Labware Training Courses, Detected Unrecognized Cli Options: --profile, How To Renewal Driving Licence, Kingdom Tower Riyadh Direction, How Many 3 Michelin Star Restaurants In The Uk, Tripura Sundari Temple Timings, Honda Gx200 Fuel Consumption,